We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Fishing Pliers Holder for Boat: How to Mount and Organize One (Beginner Guide)

Learn how to choose and mount a fishing pliers holder for boat use, so your pliers stay reachable, dry and secure during every trip.

Updated November 2026

A fishing pliers holder for boat use keeps your pliers within reach, off the deck and out of the water. In this guide you will learn what to look for in a holder, where to mount it, and how to set it up so it stays put in rough water. Most beginners only need a few basic checks and one good mounting spot.

Choose a Holder That Matches Your Pliers and Boat

Start by measuring your pliers. Note the overall length and the width of the handles, then compare those numbers with the holder’s listed fit. A holder that is too loose will rattle and let pliers slide out, while one that is too tight can scratch the coating or make the jaws hard to release.

Shopping for one? See our guide: 6 Best Van Staal Titanium Fishing Pliers for Saltwater and Freshwater.

Next, decide where the holder will live. Side-mount holders suit gunwales and console edges, while rod-tube or railing clips work better on center consoles and bass boats. Check that the mounting surface is solid, since a flimsy panel will flex under a hard pull.

Material matters as much as size. Stainless steel and marine-grade polymers resist saltwater corrosion, while plain steel will rust if spray and sun are constant. Look for stainless hardware, since fasteners are often the first part to fail.

Mount the Holder Step by Step

  1. Pick a spot within an arm’s reach of your casting station, ideally about 18 to 24 inches from the deck edge so you can grab the pliers without leaning.
  2. Confirm there is clearance behind the mount for fasteners and that no wiring, fuel lines or hatch hinges run through the area.
  3. Hold the holder against the surface and mark the screw holes with a pencil or painter’s tape.
  4. Drill pilot holes slightly smaller than your screw diameter. For fiberglass hulls, a backing plate under the mount spreads the load.
  5. Fasten the holder with stainless screws, using a sealant such as marine-grade silicone under the base to keep water out of the holes.
  6. Test the grip by inserting and removing the pliers several times, then give the holder a firm tug to confirm it does not move.

Organize Your Pliers for Quick Access

A holder works best when it is part of a simple system. Keep the pliers you use most often, such as a general-purpose pair for line cutting and hook removal, in the most accessible slot. Store specialized tools, like crimping or split ring pliers, in a separate spot or a zippered pouch so they do not clutter the main station.

If you carry a lanyard, route it through a grommet or clip rather than letting it dangle over the gunwale. A loose lanyard can snag on a line or get caught in a reel.

Mounting location Best for Main consideration
Gunwale or side rail Bass and jon boats Keep clear of rod tips when casting
Console edge Center consoles Check that the console can take screw loads
Rod-tube or railing clip Small boats with limited deck space Clamp strength must match the railing diameter

Common Mistakes

  • Mounting too far from your casting or tackle area, so the pliers end up on the deck.
  • Using non-stainless screws, which can stain the hull and loosen over time.
  • Skipping the sealant, which lets water collect inside the mounting holes.
  • Placing the holder where a hooked fish or line can tangle with it.
  • Forgetting to rinse pliers after saltwater use, even when they are stored in a holder.

A stainless steel pair of fishing pliers with a locking mechanism is a good match for a boat holder, because it resists corrosion and stays closed when stowed. View on Amazon

Stainless marine-grade screws and a tube of marine silicone make the mount last longer in wet conditions. View on Amazon

FAQ

Can I use a fishing pliers holder on a small boat?

Yes. Clamp-style or railing-mounted holders work well on small boats where drilling into the hull is not practical. Make sure the clamp fits the railing diameter.

How high should the holder sit above the deck?

Mount it at a height where you can grab the pliers without bending, usually near seated hand level. Avoid placing it where you must reach over moving line.

Does a holder replace a sheath or pouch?

Not entirely. A holder keeps pliers at your station, while a sheath protects them when you move around or store them below deck. Many anglers use both, and you can read more in Leather Fishing Pliers Sheath: How to Choose and Use One (Beginner Guide).

Conclusion

A fishing pliers holder for boat use pays off when you can grab your pliers without searching. Pick a holder that fits your tools, mount it in a solid spot with stainless hardware, and keep your most-used pair in the easiest slot. For more on tool selection, see What Are Fishing Pliers Used For? A Beginner's Guide to Each Job.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our fishing & archery gear for beginners guides, checking product details against manufacturer specifications and owner feedback.

About the author

Owen Palmer
Owen Palmer

Owen Palmer writes reviews and buying guides for Anglers and Archery.